A miter saw is a power tool that is counted in the top 10 power tools in 2020 and it is also useful for the home improvement.
Here, are some tips for using the miter saw that will help you to give the best results from your cuts.
- Let the blade stop:
You should wait for the blade to stop spinning fully. Another point to remember is to keep the miter saw’s blade in the downward position. If you pull the blade out from the material while spinning it can be possible that the tooth of the blades can broken or even harm you also.
So, just remember: Do not uplift the blade until it stops. Do the cut, let the trigger to go of and count to ten. It’s not that hard, is it?
- Mark the danger zones
While working on the miter saw, you concentrate only on your cuttings and forget the danger zones. To prevent from this, mark the lines with the red colour on the surface and fence of your miter saw. This will indicate you the danger zone and prevent you to avoid mistakes while working on the miter saw.
- For Repeat Cuts Use Stop Blocks
Besides the cutting, mostly woodworkers perform the repetitive cuts. Some projects such as garden cabinet, outdoor beverage table, DIY dog gate and outdoor coffee table comprises of many repetitive cuts. Despite of measuring each time, you should measure once and set up a stopper.
A stopper is a piece of wood from the scrap. Once the installation of the stopper is done than it would help you to cut multiple pieces of wood of same length.
This will guarantee you provide you the proper pieces along with that it will save you time.
- Use the block to Set Bevel Angles
Before the miter saw, there was no tool that can facilitate us to cut on different angles. It was difficult to cut the wood or other material at the angles but it can only possible with this power tool. It can be much easier by placing the block at the required angle.
To build the block, cut the block at 90-degree angle with no tilt. Then rotate the saw at the angle you want and it down.
- Mark the line on the blade
While making the cuts, your hands can shiver due to which you cannot get the proper and finished cuts. To avoid this, mark the straight line on the blade which help you to get the finish cuts.
- Use the stand that can move
Usually on the job site you need to constantly move the miter saw. The mobile stand will help in this way. You can easily adjust the miter saw the way you want. With the movable miter saw the task becomes as easy as eating the pie.
- You can install the laser
It helps to light the line of thin length across the work piece. It helps you to cut faster and in the exact line of the cut you want.
- Just allow the blade of the miter saw have the maximum speed
It is one of the most important tips concerning the safety measures. Once you switch on the miter saw you generally wait for it to have the maximum speed before you make cut on the work piece. Some miter saw make the smooth cut and some will not.
After you have made the cut all you need is to release your hands from the miter saw trigger and make sure to slow down the blade itself. Before the blade actually comes to rest if you lift the blade causes the off cuts fly off the table.
- Buy the saw that have double tilt
Double tilt saw or double bevel saw is much more useful than a single tilt saw. This make easier to have the bevel cuts. But if a single tilt saw is used with the better blade quality then it can make the good cuts.
- Know your hook angle
Blade with the good positive hook angle of 10 degree make the aggressive cuts on the wood. It is best to keep the angle of the blade up to 10 degree to -5 degree.
- Extend the support
Generally, the miter saw table is 18″ wide and some include the wings that extended in nature that is use to add another foot. Add the couple of scrap wood block that matches the saw table height by placing them near the board ends.
If you are working with any woodworking tool, its important to think first on the safety. Always read the instruction carefully and follow them strictly. If you are nor able to understand then contact to pro or watch videos online (YouTube will the best source).
You also need to protect your ears as miter saws makes a loud noise with the hearing protection, and your eyes with safety glasses.
It is believed that now you are much more informed about how we use the miter saw and what the tasks it can perform and what cannot. So, make sure that the miter saw is according to your needs and ensure what tasks you are going to perform with this amazing power tool.
All you need to do is to have a look on the list to know more about the product and best tools at your side. Also make sure that you have the quality product in your collection in affordable amount. This is the tip that can be useful considering the other tools also.